(1) After numbering, weighing, and registering the deer antler to the processing room, they shall be numbered (processing sequence number), listed, weighed, and registered.
(b) Washing velvety skin In order to make the velvet table clean and enhance the permeability of the antler, it is good for water dispersion and loss, and the antler table should be brushed before pilose antler processing. The method is to cut the velvet table repeatedly with a soft brush and caustic water of about 40°C, and then wash it again with clean water. After brushing, if it is processing row of bloody velvet, the antler's kerf should be directed downwards, gently squashing the antler from top to bottom to exfoliate blood.
(c) Sawing mouth This is a step of processing bloody velvet. The method is to stand the antler with the antler upright after the velvety, so as not to lose the antler blood, then sprinkle a layer of flour evenly on the kerf, and then burn the kerf with the hot iron to block the blood. Afterwards, weigh, measure, register person's account, wash antler.
(d) Treatment of damaged velvet
1 . In the case of stasis and blood stasis, which causes subcutaneous hemorrhage and congestion when colliding with the antler in the process of deer-sawn sawdust, a 40-50°C wet towel can be used to apply heat to the wound, which can spread the bruises.
2 . There is no need to deal with the old passbook that has been healed; the new passbook must be lightly wrapped around the passbook and then boiled with the inch tape. It is also possible to use a long needle to fix the medulla part of the human nail to the nail. The velvet antler pulled out after falling half dry. 3 . When the velvety skin is broken, clean the blood of the wound with clean cold water first. After the velvet skin is repaired, use a pin to fix the velvet skin on both sides of the rift, and then use a thread to wind the pin and press it; The mouth is sutured, and a layer of 0.5-cm-thick wheat flour paste is evenly spread on the cracked portion, and then boiled in water. If the velvet skin is broken, the medulla of the antler is also broken. After the velvety skin is repaired, it should be fixed with a long needle. In addition, in the case of velvet roots with too short kerfs or saws that are too close to the mouth, you can wrap 1 or 2 inches around the velvet root, and then nail it with a small nail to prevent it from boiling. Skin contraction. Too thin velvet on the shoulders, lax healing, or the old thin and thin three-arm velvety eyebrows and the abnormal protuberances near the shoulders, should be cooked in the water after cooking 1 or 2 times and apply the egg white batter, otherwise the place is very easy to be Blast the skin.
(5) When the antler is simmered and boiled on the upper velvet, it can be directly simmered at the big shoulder with the inch ribbon (especially for processing with bloody velvet, and it is not necessary to clip the velvet when frying it), but when processing the velvet, People are used to fixing the antler on the antler. If using a swarf clip with a stencil card, clamp the antler root from 0.7 to 1.1 cm from the clevis to the middle of the sprocket and tighten the screw (Fig. 10-1). If using a wooden velvet clip, fix it with an antler. Saw both sides of the front and rear oblique nails two 7 - 8 cm long nails, left and right sides of each nail a nail 5 centimeters, the antler erected in the antler clip, with a rope wrapped around the front and rear fixed head velvet The fixing method is to lift and spread the scalp and clamp the head of the scalp.
The deer industry association unit of China deer industry---Jiulu Luye Group, Beijing Jiulu Luye Sika Deer Breeding Base, Beijing Management Headquarters Company has set up large-scale deer breeding farms, deer product stores, deer full-scale restaurant and other industrial chains. Luye Deer Farm Address: Xiaoganhao Industrial Park, Jingcheng Town, Tongzhou District, Beijing Jiulu Deer Industry Jiulu Deer Industry Company Address: No. 32, Caojingxi, Yunjingli Street, Liyuan, Tongzhou District, Beijing Jiulu Lubaotang Jiulu Deer Industry official 24-hour consultation hotline Jiulu deer industry official QQ
Jiulu Deer Industry Website: http://
Omega-3 Fish Oil,Fish Oil 10/50 Tg,Omega 3 Fish Oil,10/50 Tg Fish Oil
ZHOUSHAN SINOMEGA BIOTECH ENGINEERING CO.,LTD , https://www.sinomegabiotech.com