Judgment on tractor malfunctions

The non-demolition inspection method is a practical technique for judging tractor failure without disassembling the machine. This method can avoid the loss and waste caused by the blind disassembly, which is a good method for high efficiency and low consumption. The seven kinds of non-demolition inspection methods that are commonly used are described as follows: The inspection method judges the failure of the machine by looking at the appearance of the machine for abnormalities. Such as exhaust pipe smoke color; machine appearance with or without "four leakage" phenomenon; oil temperature, oil pressure is normal; light is bright; The feeling method uses the sense of smell and hand touch to judge and analyze the cause of the malfunction. If you touch the bearing shell, feel the temperature change; touch the high pressure tube to feel the pulsation strength of the oil pressure; the nose olfactory friction sheet has no burning odor and so on. The auscultation method uses a special stethoscope or a long screwdriver to select appropriate parts for auscultation in a certain order. The auscultation site should generally be selected on the side of the housing of the auscultation part. The sound of the various mating parts of the tractor that move with each other and strikes can usually be distinguished by the fact that small parts touch small parts with small sounds and are crisp and sharp; large parts touch large parts with loud and heavy sound; small parts touch large parts and are similar The hammer strikes the anvil; the shaft collides with the bearing, and the sound is dull. When the heuristic suspects that the fault is in a certain location, but cannot be fully affirmed, he or she will perform a tentative examination of the suspected component and determine the true cause of the fault based on the change in the fault signature after the exploratory inspection. For example, in order to diagnose the cause of the “discharge black smoke” sign, try to adjust the pressure value of the fuel injector. If the “black smoke” sign disappears after adjusting the injector pressure, it can be concluded that the cause of the fault is a spray. The grease pressure is too low. The cylinder-cut method stops the fuel supply or ignition of a certain cylinder in sequence, and observes the change of the fault sign to judge which cylinder has failed. When the replacement method analyzes a fault, it has suspicions about a certain part or part, and replaces it with a spare part with good technical condition. Then, according to the change of signs before and after the change of parts, it is determined whether the technical status of the original part is normal. For example, the hydraulic suspension mechanism cannot be lifted, and it is suspected that the failure is in the distributor. Therefore, a distributor with a good technical condition is put on the test. If it cannot still be lifted, the failure is not in the distributor. The screening method is troublesome for some inconvenient inspections or inspections. There is no failure factor of the inspection method. It does not directly check, but through other failure factors in order to check and eliminate, and the last remaining failure factor is to initiate the failure. the reason.

What is Ultrasound fat slimming
Ultrasound Liposuction (ultrasonic cavitation) is a new, revolutionary fat removal technique that does NOT involve surgery – there is no need for anaesthetic, a hospital stay or time off work.

The treatment has immediate results and delivers further additional fat reduction within the week following the procedure.

Ultrasonic Slimming utilises a unique cavitation technology new that allows for non-invasive removal of stubborn fat deposits that never seem to disappear regardless of your diet or how hard you work out.

The most problematic body areas are: abdomen, flanks ([love handles"), thighs ([saddle bags"), buttocks, inner knees, upper arm, male breasts.

How does it work
The Ultrasonic treatment safely and effectively targets localized fat deposits and reduces body circumference for successful body contouring. this procedure is done per area on specific parts of the body, such as saddle bags, buttox, stomach, love handles, arms, and inner thighs.

A hand piece device uses ultrasonic waves that penetrates through the epidermis and dermis to the subcutaneous fat. Emulsified fat is carried to the liver through normal metabolic tracks. Action caused by the equipment on the person`s organism could be defined as lipolysis through local ultrasonic cavitation therapy.

Benefit of Ultrasound cavitation slimming treatment
Our Ultrasonic Slimming process removes fat cells permanently through the process of cavitation.It Improves skin texture and tightness and enhances body tone and shape.

No anaesthetic, no surgery and no pain (a HUGE benefit!)
Great results naturally – our process inproves blood circulation and lymph circulation

An excellent cellulite therapy and connective tissue tightening process

Key Benefits of Ultrasonic Slimming sessions:
Fat removal and cellulite reduction
Enzymatic liposis, skin toning
General reduction of waist, abdomen and buttocks (i.e. drop dress/suit sizes!)
Body shaping and contouring
Skin tightening and rejuvenation, improved elasticity and tone

Scars and wrinkle smoothing

*Related Products:Body Shape Machine,Slimming Machine.

Cavitation & Slimming

Cavitation Rf Weight Loss Body Slimming Machine, 6 In 1 Ultrasonic Liposuction Cavitation Rf Slimming Machine, Weight Loss Slimming Machine,Body Shape Machine,Slimming Machine

Zhejiang Lasy Science and Technology Co.,Ltd. , http://www.lasylaseripl.com